Hot Tub With Fire Photo #4 - Bonsall Pools & Spas

BioGuard Back Up 2 Algaecide is BioGuard’s most effective algae preventative. The highly effective formula prevents wide variety of algae growth. It’s stable in sunlight and will not evaporate. The activity of this product increases as water temperature rises, which is when you need protection the most. Back Up has a powerful surfactant/wetting agent, which makes it able to work in the tiny cracks and crevices where algae starts. This product will not affect pH levels and is non-staining.

Pre-Treatment Checklist:

Ensure all pool equipment is working properly. Clean or backwash the filter following manufacturer’s directions.
Adjust stabilizer levels to 30-50 ppm by adding stabilizer.
Check water alkalinity, pH, and calcium hardness with a test kit or test strip. Adjust alkalinity to 80-125 for plaster pools, 125-150 ppm for vinyl or fiberglass pools by adding an alkalinity increaser. Adjust pH to 7.2-7.8 by adding a pH decreaser to lower the pH, or by adding a pH Increaser to raise pH. Adjust calcium hardness to 200-275 ppm for plaster pools, and 175-225 ppm for vinyl or fiberglass pools by adding a calcium hardness increaser.
Check and adjust residual chlorine level to desirable range of 1-4 ppm.

This product is effective in controlling algae growth of both green and black algae. Add this product directly to the pool by pouring around the outside perimeter of the pool while filter and pump are in operation.

Wait at least 15 minutes after application before entering pool.

Pools With Visible Algae:

If algae is visible, use 13.5 fl oz of this product per 10,000 gallons of pool water. After 24 hours clean out dead, settled algae. If algae is still present, repeat dosage if necessary.

Initial Application or When Pool Water is Changed:

Add 6 fl oz directly into pool per 10,000 gallons of water.

Routine Maintenance:

For weekly application intervals, add 1.5 oz. per 10,000 gallons of water every 5-7 days

Booster Application:

Add an additional 1.5 fl oz per 10,000 gallons of pool water following heavy or prolonged rain showers and heavy bather loads.

Vacation Treatment:

Add 4 oz. of this product per 5,000 gallons for every week unattended. Pour product around the edges of the shallow end of the pool if shock is also being applied in the deep end of the pool.

BioGuard Algae All 60 is a highly effective algae preventative. It is recommended by the manufacturer for use with pools with attached spas or jetted returns. This product treats stubborn algae growths in chlorine or bromine pools. It is formulated to be non-foaming and non-staining. This product is effective on all types of algae and works in all pH ranges. Algae All 60 will not affect pH level.

Pre-Treatment Checklist:

Ensure all equipment is working properly.
Backwash the filter system following manufacturers directions.
Adjust the pH to between 7.2-7.6.
In chlorinated systems, add stabilizer to establish a minimum stabilizer level of 30-40 ppm to reduce the degradative effects of sunlight upon the chlorine residual.
Check for metals and if present add a stain and scale inhibitor to prevent staining of pool surface due to metals.
Adjust chlorine residual to 1-3 ppm. When using other products as outlined in directions for this product, always follow directions on those products.

Standard Application:

For pools having light algae growth, pour the initial dose of 11-17 oz. per 10,000 gallons of water directly into pool.
Remove settled algae debris by cleaning.
For treatment of a freshly cleaned and filled pool, pour the initial dose of 6-11 oz. per 10,000 gallons of water directly into pool.
Additions of 2-4 oz. of this product per 10,000 gallons of water should be made every 5-7 days after initial treatment for maintenance.

Wait at least 15 minutes after application before entering pool.

BioGuard Algae Complete is an extremely efficient, and a rapid working algae eliminator. All types of algae do not stand a chance against this product, some of them for an example are green algae, mustard algae, and black algae. Algae Complete was designed to be compatible with most swimming pool sanitizers, and is a non-foaming product. When used correctly, this product is profoundly effective.

Kills and prevents all types of algae
Works with most types of sanitizers (Except biguanide)
Formula does not stain pools

Prior To Application

Ensure all equipment is working properly. If necessary clean the filter system.
Adjust pH between 7.2-7.6
Establish and maintain proper chlorine or bromine levels. In chlorine-treated pools, add stabilizer to establish a minimum level of 30-40 ppm of cyanic acid to reduce the degrading effects of sunlight on chlorine residual.
Vacuum leaves and any other foreign debris from pool.
Brush visible algae thoroughly from the pool’s surface with a surface-compatible brush.

To Prevent Pool Algae

Initially apply 8 ounces of this product per 10,000 gallons of pool water.
Thereafter, for weekly application add 1-1/2 ounces per 10,000 gallons of pool water. For two week application intervals add 3 ounces per 10,000 gallons of pool water every other week. Apply more often if pool volume is diluted by heavy rain, frequent backwashing or partial drain/refill.
Wait at least 15 minutes after application before entering pool.

Treatment Of Visible Pool Algae

Apply a BioGuard oxidizer per label directions.
Allow to circulate for 1 hour.
With pump and filter operating, apply 16 fluid ounces of this product per 10,000 gallons of pool water directly to the pool water in areas of heaviest algae growth.
Continuously circulate pool water for 24 hours.
The next day, thoroughly brush pool surfaces.
Prior to re-entry, test chlorine level. Do not enter pool until chlorine level is between 1-4 ppm.
In cases of persistent algae, repeat brushing and product application after 2-4 days.

BioGuard Spot Kill eliminates algae quickly and easily. It is highly soluble which makes it compatible for most pool surfaces. This product is approved for use in pools sanitized with chlorine and bromine (and should not be used in Soft Swim pools). The granular formula allows for direct application into the pool. This product is near pH neutral and will not upset the water balance. Spot Kill kills green or black algae.

Ensure all pool equipment is working properly. Backwash the filter system following manufacturers directions.
Adjust pH to between 7.2-7.6.
Check for metals and if present add stain and scale inhibitor to prevent staining of pool surface.
When using other products as outlined in the directions for this product, follow directions on those products.
Before using this product, brush all surface-clinging algae paying special attention to pool steps, ladder steps and around skimmer and lights. At night, or when the pool is not in use, broadcast this product directly into the water in the deep end of the pool with pump running.
Use 2 pounds of this product per 10,000 gallons for medium to heavy algae growth and 1 pound per 10,000 gallons for light algae growth.
To prevent possible damage to pool surface, use a pool brush to disperse any granules that may have settled to the bottom of the pool.
Brush any remaining algae and clean/backwash filter. If algae is still visible, repeat treatment.

Spot Kill WP is a highly effective, fast-acting black algae destroyer. This product may be used in chlorinated or brominated pools. Use this product only in WHITE PLASTER POOLS. DO NOT USE this product in painted, vinyl lined, fiberglass or colored plaster surface pools as damage may occur to the pool surface.

DO NOT USE THIS PRODUCT IN POOL SURFACE TYPES OTHER THAN WHITE PLASTER.

Clean the filter and adjust water balance.
Adjust chlorine residual to 1-3 ppm and establish a minimum level Stabilizer level of 30-40 ppm.
If any metals are present, add Scale Inhibitor according to label instructions.
Turn off pump and brush algae growth vigorously.
Wait 4 hours or until water is still.
At night or when the pool is not in use, broadcast Spot Kill WP around edges of the pool and directly over growth into the water. Use 1 lb. per 10,000 gallons for light growth. Use 2 lbs. per 10,000 gallons for medium to heavy growth.
12 – 24 hours later vacuum, brush dead algae and backwash.
Repeat treatment if living algae is still present.
Do not allow swimmer reentry until the free chlorine residual returns to 1 – 4 ppm.

BioGuard Banish kills ALL types of swimming pool algae. This fast acting formula will produce results in just 24 hours. This product allows swimmers to return soon after treatment. It is formulated to clear up water while it kills the algae and is approved for use in chlorine and bromine pools. Banish does not affect pH levels, so no readjusting is necessary after application. This product is also approved for use during shock treatments, so there are fewer steps than when using other copper-based algaecides.

Prior to application:

Ensure all equipment is working properly. If necessary, clean the filer system, adjust pH between 7.2-7.6, and establish a minimum level of 30-40 ppm of stabilizer in chlorinated pools. Vacuum leaves and any other foreign debris from pool. If metal testing indicates a need to use a stain and scale inhibitor, apply that product per label directions. Brush visible algae thoroughly from the pools surface with a surface-compatible brush. Establish and maintain proper chlorine or bromine levels.

To Prevent Pool Algae:

Initially apply 8 oz of this product per 10,000 gallons of pool water with pump and filter operating.
Thereafter, for weekly application intervals, add 1.5 oz per 10,000 gallons of pool water. For two week application intervals, add 3 fl oz per 10,000 gallons of pool water every other week. Apply more often if pool volume is diluted by heavy rain, frequent backwashing or partial drain/refill.
Wait at least 15 minutes after application before entering pool.

Treatment of visible algae:

Add 1 lb of BioGuard Maintain BurnOut 3 per 10,000 gallons of pool water or 1 lb Burnout 35 per 6,000 gallons of pool water or 1 lb BioGuard Smart Shock per 12,000 gallons of pool water. Follow application directions on these products.
Allow to circulate 1 hour.
With pump and filter operating, apply 16 oz of this product per 10,000 gallons of pool water directly to the pool water in areas of heaviest algae growth.
Continuously circulate pool water for 24 hours.
The next day, thoroughly brush pool surface.
Pior to re-entry, test chlorine level. Do not enter pool until chlorine level is between 1-4 ppm.
In cases of persistent algae, repeat brushing and product application after 2-4 days.
The use of a filter aid will enhance filter efficiency and algae removal
Chemically cleaning the filter is recommend 3 to 4 days after treatment.

100% Sodium tetraborate pentahydrate
pH 9.3
Improves water quality while suppressing algae growth
Softens water
Test and add

Balance your pool water and adjust pH to between 7.2–7.6.
Add 2 pounds of this product per 1,000 gallons of pool water (this gives approximately a 35ppm residual) by broadcasting the product over the surface of the pool with the pump running.
BioGuard recommends this initial treatment should be added in three doses with 1/3 of the required amount being added each application.
Brush any undissolved product from the bottom of the pool.
The pH of the pool water will rise as a normal reaction to the introduction of this product. One hour after each application, adjust the pH to 7.2–7.6 with BioGuard Lo’N Slo®.
Allow at least 8 hours between the applications of Optimizer Plus.

Note: For every 2 pounds of Optimizer Plus, approximately 1 pound of Lo ‘N Slo® will be required for pH adjustment.

BioGuard Stabilizer 100 is a granular, totally soluble product that prevents free chlorine residual loss due to sunlight. Without Stabilizer 100, chlorine quickly dissipates and consumption increases. This product is formulated to reduce maintenance costs and chlorine consumption. It is intended only for outdoor, chlorinated pools. The key ingredient of this product is cyanuric acid.

Use 1 pound of this product per 3,000 gallons of pool water to provide an intial stabilizer level of 40 ppm. The use of 1 pound per 4,000 gallons of pool water will provide an intial stabilizer level of 30 ppm. Broadcast directly into pool, scattering over the surface of water. For pools with plastic piping, this product may be slowly added through the skimmer. Keep the water circulating continuously for 24 hours after addition. When the product reaches the filter there may be a temporary increase in filter pressure which will dissipate as the product dissolves. Do not backwash for 48 hours after application of this product.

BioGuard Instant Stabilizer 100 (1 gal) prevents the flood of free chlorine due to sunlight. This quick-dissolving formula is easier to apply than granular stabilizer. Protecting your chlorine with this product reduces chlorine consumption and maintenance costs.

Shake Well.
With circulation pump running, slowly pour BioGuard Instant Stabilizer 100 into pool skimmer or directly into pool while walking around the edge of pool. Brush to rapidly disperse product.
Rinse container with pool water and shake to ensure all product is removed from the bottom of the bottle.
Pour remaining rinse solution into the skimmer or pool.

Dosage Tips:

1 gallon of BioGuard Instant Stabilizer 100 raises CYA levels by 32 ppm per 10,000 gallons.

Note: If CYA level is less than 30 ppm, calculate gallons of BioGuard Instant Stabilizer 100 need by using the following formula:

4 fl oz added to 10,000 gallons = 1 ppm increase of conditioner stabilizer level.

BioGuard Lo N Slo reduces pH and total alkalinity in pool water. This product is generally easier to use and store than liquid muriatic acid. Keeping your pool’s pH level balanced is not only important for swimmer comfort; it also helps keep your equipment and pool finish in good condition. Swimmers may return to the pool only 15 minutes after application. You can slowly and safely reduce pH and total alkalinity with Lo N Slo.

Balance the total alkalinity in the pool water to 125-150 ppm. Pool pH should remain between 7.2 and 7.6 for the most effective use of chlorine. Test the pH using a reliable test method such as BioGuard 4-Way Test Strips. If the test shows a pH above 7.6, then add this product to the pool water using the recommneded dosage.

Add this product when the pool is not in use. Broadcast product into the deep end with the pump and fiter running. Never add more than 1.5 lbs of this product per 10,000 gallons of pool water at any one time. Allow the pool water to recirculate for two hours and retest the pH. Repeat teatment as necessry. Newly plastered pool may require frequent treatments for the first frew weeks whil the pool is “curing”. Do not add the product near metal fittings or allow the pH to drop below 7.2. Break up undissolved clumps of product that may remain on the bottom of the pool.

Do not add this product directly to pools with colored plaster surfaces. Choose one of the following methods for application. Method 1. Predissolve this product in a bucket of cool tap water, adding no more than 1 pound of product for each 3 gallons of water used for predissolving. With circulation pump operating, pour the solution into pool water in an area of strong circulation from a return fitting. Operate the circulation pump continuously for the next 8 hours. Method 2. Do not use this method for pools with metal plumbing, stainless steel filter housing or metallic pump impellers. Remove all products from the skimmer. With the circulation pump operating, apply the appropriate dosage slowly into the skimmer. Apply at a rate not faster than 1 pound per minute. A slight increase in filter preasure may be observed, but is not cause for concern. Operate the circulation pump continuously for the next 24 hours. Do not add any granular or liquid products to the skimmer of the pool during this 24 hour period.

BioGuard Balance Pak 200 raises pH in pool water. Keeping your pool’s pH level balanced helps prevent equipment corrosion, etching of plaster, and wrinkling of liners caused by low pH. It is also important to swimmer comfort as it prevents eye irritation due to low pH. In addition, many algaecides require the pH to be balanced in order to work properly. Keep your pool in proper balance with Balance Pak 200.

To raise pH, distribute a maximum of one pound per 10,000 gallons of water, directly into the deep end of the pool. Allow water to recirculate two to three hours, recheck pH, and repeat treatment if necessary.

BioGuard Balance Pak 100 is used to raise total alkalinity. Maintaining proper total alkalinity prevents pH from bouncing due to rain, bather load, and other chemical applications. Low alkalinity may also cause pool water to be corrosive to the metal and plastic with which it comes in contact. This product is proven to help prevent pool staining, plaster etching or liner wrinkling. The contents of Balance Pak 100 dissolve quickly when added directly to water.

Add directly to the pool with the pump and filter running.

BioGuard Balance Pak 300 is a calcium hardness increaser. This product boosts calcium hardness to help prevent equipment corrosion, etching of plaster and wrinkling of liners. It has a unique pelletized formulation which means faster dissolving and less cloudiness. Low calcium hardness can cause staining, etching, or distorting of the pool’s finish. Plaster etched by low calcium hardness will become abrasive and uncomfortable for swimmers. Rough plaster also increases algae problems and makes cleaning more difficult. It is important to keep your pool water balanced in order to get the most effective use out of your chemicals.

Calcium Hardness in pool water should be maintained in the 175-275 ppm range. Never allow calcium hardness to remain below 100 ppm. Add this product directly to pool water by scattering it over the water surface. Do not predissolve this treatment as heat is generated when this product contacts water. Use surface compatible brush to brush away undissolved granules off pool surface. The addition of 4 lbs. of this product per 10,000 gallons of water will raise calcium hardness approximately 40 ppm. The addition of 10 lbs. of this product per 10,000 gallons of water will raise calcium hardness appoximately 100 ppm.

BioGuard Pool Magnet Plus prevents staining due to iron, copper and manganese. It also eliminates discolored water from metals. This product has been recently reformulated and is now more concentrated and effective as ever. Pool experts recommend that this product be used monthly in pools that hold iron-containing fill water. It is only necessary to be used monthly because it stays effective for 3-4 weeks. It is recommended to use Pool Magnet Plus in conjunction with BioGuard Sparkle Up to remove metals from the water.

Stain Prevention:

To treat for metals in pool water, backwash filter, then allow pump to run continuously. If the total amount of metals present exceeds 1.0 ppm also use BioGuard Sparkle-Up Filter Aid to assist in metal removal. Use 1 quart of this product per 10,000 gallons of water per 1.0 ppm of metals. Maximum recommended dose is 3 quarts per 10,000 gallons. If pool has been shocked , wait 24 to 48 hours before applying this product to obtain maximum effectivenes. Add directly to the pool in the area of any localized metal stains. Some temporary clouding may occur. Product should be added when chlorine is 1.0 ppm or less and 7 days prior to superchlorination to minimize staining potential. Backwash the filter as indicated by pressure build up. Never allow filter pressure to exceed the limit established by the manufacturer.

Maintenance Dose:

When make-up water contains metals, add 3 oz. of this product per each 1,000 gallons of water added to the pool.

Removal of Fresh Stains:

Many fresh metallic stain can be removed by the action of this product. Turn circulation off for 8 hours. Slowly, and as close to the surface of the water as possible, pour one to three (depending on severity of stains) quarts of this product directly in the area of the the stain. Do not swim or operate pump for 24 hours. After waiting period, turn pump on, circulate water, and brush pool for 5 to 7 days. Use BioGuard Sparkle-Up in the filter to remove redissolved metals. Repeat treatment for large metal stains. For white plaster pools where large metal stains have aged into the pools surface, draining and acid-washing is recommended. Consult your BioGuard Dealer regarding this procedure.

BioGuard Scale Inhibitor prevents scale build-up from high calcium levels. It also prevents stains caused by iron, copper and manganese. This product has recently been reformulated and is four times more effective than it was previously. Regular use of this new concentrated formula prevents scale build-up on pool surfaces, piping, filtration, and heating elements. This product will not affect pH. Scale Inhibitor will continue working 3-4 weeks after application.

Initial Treatment:

Backwash filter according to manufacturers directions. With the pump running add 1 quart of this product per 10,000 gallons of water, pouring product directly into the pool. Continue to run pump for 24 to 48 hours after this addition.

Maintenance Treatment:

For the maintenance dose, apply 16 fl. oz. of this product per 10,000 gallons of pool water once a month. Add product directly to pool water with pump on. Maintenance doses should be used for pools in areas where excessive hardness or metals cause constant scale and staining problems.

Fresh Stain Removal:

Many fresh (less than 5 days old) metallic stains can be removed by this product. Add this product at a rate of 1 quart per 10,000 gallons of water. Apply directly to the pool in the area of the stains. Brush the stained area daily for 3 to 5 days. Large metal stains may require repeat treatments. Where metal stains have aged into the pools surface, draining and acid washing is recommended for white plaster pools only. Consult your BioGuard dealer regarding this matter.

BioGuard ChemOut eliminates chlorine, bromine, or hydrogen peroxide deposits in pool water. This product is intended to reduce swimming downtime due to high chlorine levels. It will not affect pH levels, so there will be no readjusting necessary after use of this product. ChemOut is also great for neutralizing chlorine or bromine when converting a pool to Soft Swim. In addition, it is sometimes necessary to lower chlorine or bromine levels when treating severe metal stains and when dealing with metal problems.

Allow at least 8-12 hours for superchlorination treatment to oxidize wastes and chloramines from the pool water. Add BioGuard ChemOut to lower the free chlorine reading to the required 3.0 ppm level before swimming. Before adding any product to the pool, measure the free chlorine in the water. This must be done to determine the correct dosage of BioGuard ChemOut.
To Measure the free chlorine in water, test using either a BioGuard water test kit or the BioGuard 4-way Test Strips. First, test the superchlorinated pool as you would normally. If the available or free chlorine reading is above the highest level shown on the tests color comparitor or to get a more definitive result at high chlorine levels, it may be necessary to dilute the water sample. To dilute the water sample, using a measuring cup, add one cup of pool water to one cup of tap water. Gently stir the diluted water and then test the diluted water using either BioGuard water test kit or BioGuard 4-way test strips. When you have determined the free chlorine level of the diluted sample multiply this level by 2. You now have the free chlorine level of the pool.
To calculate the ppm available chlorine that must be removed from the pool, subtract 3 ppm from the free chlorine level of the pool. The resulting number is the amount of free chlorine you must remove before it is safe to swim. Use the chart on the bottle to calculate the required dose using the measuring cup supplied with this product. Add this product directly to the pool scattering around the edge of the pool. Keep the pump on and water circulating.
Do not add treatment through skimmer.

BioGuard StowAway cleans and deodorizes pool covers to prepare them for storage. Even when pool covers are stored wet, this product cleans, deodorizes, and prevents the cover from sticking together when it is folded. StowAway aids in stain and soil removal and extends the life of most covers. It is a versatile product that may be used on solar covers, pool umbrellas, and other pool-side items. Prepare your pool cover for storage the right way with StowAway.

While cover is still on pool, remove all debris and water from cover.
Remove cover from pool and spread on lawn, pool deck, or driveway.
Squirt this product over the entire cover and brush clean (A nylon bristle pool brush and telescopic pole are excellent for this purpose).
Rinse off loosened soils with water.
Fold pool cover, squirting this product full strength between each fold.
Store folded cover in a safe place.

BioGuard Erase Iron Stain Remover is specifically formulated to combat iron-based stains, restoring your pool surfaces to their former beauty. Its proprietary granular formula can be added directly to pool water over the trouble areas, and is compatible with plaster, tile, and vinyl surfaces to accommodate virtually all pools. It can even be used to remove cobalt staining on fiberglass pools! Best of all, Erase Iron Stain Remover is made by BioGuard, an industry leader for decades, allowing you to buy with confidence.

Pre-Treatment:

If your swimming pool is equipped with a heater, first turn the heater off, then isolate from the circulation system.
In order to prevent damage to your swimming pool, do not allow un-dissolved particles to sit on surfaces for more than 30 seconds.
Adjust the chlorine/bromine residual to less than 1 ppm (for Softswim pools, a B residual of 30 to 50 ppm).
Adjust pH to between 7.0 to 7.4.
Adjust alkalinity to between 125 to 150 ppm (or 80 to 150 ppm if using a salt generator).
Adjust calcium hardness to less than 400 ppm.

Stain Treatment:

Wearing safety glasses/goggles and with the circulation pump running, add 2 lbs of Iron Stain Remover per 12,000 gallons of pool water. Add the product along the edges of your pool for even distribution. If stains are concentrated in any one area, apply product over it. Use a surface compatible brush to disperse any un-dissolved particles.
Allow water to circulate for 1 hour, then apply the correct dosage of Pool Magnet Plus (or Softswim Stain Control for Softswim pools) per label directions.
Allow pool to circulate water for 24 hours.
Apply Sparkle Up (or Softswim Filter Aid for Softswim pools) from filter by backwashing or cleaning cartridges.
Apply BioGuard Kleen It (or Softswim Filter Cleaner for Softswim pools) according to label directions to remove any trapped metals in the filter itself. Complete stain removal may take up to two weeks or require a second treatment.
Readjust water chemistry back to optimal ranges (pH between 7.2 to 7.6, alkalinity 125-150 ppm or 80 to 150 for pools with salt generators). Also readjust chlorine/bromine or Softswim sanitizers to correct levels as determined by label directions. Softswim pools also need to adjust Clarifier levels to 30 ppm.
After treatment is complete, use Pool Magnet Plus or other metal-preventing chemicals to stop metals from building up in your pool water. For Softswim pools, use Softswim Stain Control. Always follow label directions when adding chemicals.
A repeat treatment may be necessary if stains are still present 48 hours after completing the treatment cycle.

Do not apply any shock treatment to the pool water for 4 days following completion of step 3.

BioGuard Strip Kwik is an effective degreaser that unclogs your sand, cartridge and DE filter, restoring it to optimal efficiency. Its patented formula quickly cuts through the thickest oil, grease, dirt, and other contaminant buildup on your filter elements to greatly extend its lifespan, saving you money over the course of the pool season. Strip Kwik also is able to clean your filter in about an hour instead of overnight soaking like its competitors. Best of all, this product is made right here in the USA to ensure the highest quality, allowing you to buy with confidence.

DE and Cartridge Filters:

Rinse the cartridge or element with a garden hose prior to applying product. Using a clean spray bottle with full strengh product, evenly coat elements or cartridge. Wait 10 minutes and then rinse thouroughly with a garden hose for 5 minutes. Then, using a large clean plastic bucket, soak for 1 hour in a solution of 1 part Strip Kwik and 3 parts water. Rinse thoroughly with a garden hose before use.

Sand Filter Initial Dose:

Remove any chlorine product from the skimmer prior to product application. If the pool is equipped with a chemical feeder (chlorinator or brominator) this device should be turned off by closing the inlet valve prior to product application. Backwash the filter as normal. Turn off pump. Pour the appropriate amount of product directly into the skimmer. See the dosage chart above for the exact amount to use with your filter type. Turn the pump on long enough to allow product to move into the filter. Turn pump off. Wait 1 hour with pump off. With the filter selector in the backwash position, turn the pump on and backwash until waste water is clear. Do not allow product to return to the pool.

Sand Filter Maintenance Dose:

This product can be used at every backwash to prevent the buildup of grease and oil. Remove any chlorine product from the skimmer. If the pool is equipped with a chemical feeder (chlorinator or brominator) this device should be turned off by closing the inlet valve prior to using this product. While the filter is backwashing, add 8 ounces of product directly to the skimmer. Do not allow product to return to the pool. Continue backwashing until the waste water is clear.

BioGuard Kleen It Filter Cleaner is designed to remove scale/clarifier deposits, dirt, and debris from the pool’s filter. This product is comprised of a dual action formula that can prolong the life of your filter. It helps prevent scale build up and rust. The experts recommend that this product should be used at least once per season to keep the filter clean. Kleen It has been proven to not damage the filter equipment and to be safe for all filter types.

Non Back-Washable D.E. & Cartridge Filters:

Turn pump off and rinse off loose dirt from filter elements.
Apply product by spraying directly onto filter elements. If needed, lightly brush heavy grease spots.
Let wet filter elements sit for 5-10 minutes. For heavily soiled filters, allow elements to sit for 1 hour.
Rinse elements thoroughly with full-strength water from a garden hose.
Reassemble filter and resume normal operation.

As an alternative soak filter elements overnight into a solution of 32 oz. of this product added to 5 gallons of water. Allow to soak overnight. Rinse elements thoroughly with full-strength water from a garden hose.

Sand Filter & Some D.E. Filters:

Twice each pool season, mid-summer, and in the fall, clean the pool filter as follows: Backwash filter thoroughly. Turn pump off. Chlorine must be removed from the skimmer basket prior to addition of this product. Automatic feeder should be turned off prior to any addition of this product. Pour entire bottle of this product into skimmer. Turn pump on until pump primes and product moves into filter. Leave filter selector in backwash position or in closed position. Wait one hour. Turn pump on with selector in backwash position, until backwash water is clear.

BioGuard Anti Foam is an excellent way to remove annoying foam buildup in your pool, spa, hot tub or ornamental fountain, leaving your water crystal clear in seconds. Foam can build up because of lotions, oils, soaps, and other organic compounds left by swimmers or bathers and react with chemicals in your pool. Anti Foam’s powerful liquid formula neutralizes it quickly and can be used multiple times on especially heavy buildup without fear of any adverse reactions. Best of all, this product is made right here in the USA to ensure the highest quality, allowing you to buy with confidence.

Use 2 ounces of this product per 5,000 gallons of water to prevent and eliminate foaming in swimming pools. Use 1 teaspoon of this product per 200 gallons of spa or hot tub water to prevent and eliminate foaming in water. The amount of this product required depends on the conditions of the tub or pool and the amount of foam present. Repeat this dose as needed to control the foam. Once this product is introduces, the effect on the foam should be immediate. Large quantities may be required where tubs or pools have been vandalized by the addition of soaps or detergents.

BioGuard Burnout 3 is a high-powered chlorine shock that will quickly kill off any bacteria or other organic contaminants, restoring your pool water to clarity and health. Its quick-dissolving granular formula can be added directly to pool water without messy pre-dissolving, making application easy and hassle-free. It is designed specifically to work safely in vinyl and plaster pools without fear of bleaching, and is also compatible with chlorine and bromine sanitizers. Best of all, Burn Out 3 is made to the exacting standards BioGuard demands of all its products, allowing you to buy with confidence.

With the pump running, broadcast the product evenly into the deep end of the pool.
Continue to operate recirculation pump for 4 to 8 hours (24 hours for Algae Kill) after product addition. In pools with potentially bleachable surfaces, such as vinyl, plaster, fiberglass, or colored plaster, brush any undissolved product from pool surfaces.

Never allow undissolved product to rest in contact with bleachable pool surfaces.

In shallow pools with a depth less than 4 feet or when water is less than 65 degrees F, predissolve this product and apply evenly around the edge of the pool. Dissolve this product outdoors in a clean plastic bucket, stirring with a clean plastic or wooden spoon.

Add this product to water, NEVER add water to product. NEVER add more than 1 pound of this product to less than 3 gallons of pool water. NEVER mix with any other products.

BioGuard Easy Shock & Swim is a tried and true multi-purpose shock, which provides oxidation, clarification, buffering, and flocculation in one easy-to-use product. This product is an excellent choice for all swimming pools, especially above ground swimming pool models. It is suitable for use with Nature 2 and Frog pool systems. With this product, you can treat and swim in as little as 15 minutes. Easy Shock & Swim will not affect pH levels and there is no premixing required.

With the pump in operation, apply the entire dosage at one time. Broadcast evenly around edges with special attention to areas of the pool where water circulation is the poorest. Apply directly to pool water only. Do not add through skimmer or any automatic dispensing device.

For best results, test and adjust pH to 7.2-7.6 prior to application. Apply product when pool is not in use. Swimming may resume in as soon as 15 minutes after product application. Test chlorine residual. Swimming may resume when chlorine residual is 1-4 ppm.

BioGuard Oxysheen is a non-chlorine pool shock treatment. It will destroy contaminants such as perspiration, sun tan oils, and other impurities that can affect swimmer comfort. By destroying organic waste, this product can lower your sanitizer consumption, as well as brighten and clarify your pool water. This product dissolves rapidly and completely, so swimming can resume just 15 minutes after application. Restore sparkle and clarity to your pool water with Oxysheen.

Broadcast the required amount of this product directly into the deep end of the pool with the filtration sytem running.
Apply in the morning or evening when no bathers are in the water. Swimming or bathing may be resumed in 15 minutes.
Maintain pH in the range of 7.2-7.6, total alkalinity in the range of 100 ppm to 150 ppm, and calcium hardness in the range of 150 ppm to 300 ppm.

BioGuard Burnout 73 is a superchlorinator for swimming pools. With the highest percentage of calcium hypochlorite of all the BioGuard shocks this one bag treats 16,500 gallons of water making it one of the strongest shocks on the market.

Note: Never add water to product. Always add product to large quantities of water to fully dissolve. Maintain operation of your pump and filter. Treatment should be done at night or during a period when the pool is not in use. This product can be added by broadcasting the dry granules over the surface of the water at the deepest end of the pool while the pump is running.

Shock Treatment / Superchlorination:

Adjust pH between 7.2 and 7.4 prior to shocking or superchlorination. Add this product at night or when the pool is not in use. To prevent pool water problems, shock at least once per week during periods of heavy use or when water temperatures are above 80 degrees Fahrenheit and once every two weeks in resident pool receiving normal usage. Maintain operation of the pump and filter. Do not enter the pool until the free chlorine residual has dropped to 4.0 ppm or less as measured using a suitable test kit. Between treatments with this product, continue to maintain the proper water balance and sanitizer level in your pool as recommended on the label of your normal pool sanitizer.

BioGuard Smart Shock is a multi-functional product that shocks, oxidizes, buffers, and clarifies pool water. It kills and prevents bacteria growth. This product has unique blue algae-fighting crystals that kill unsightly algae. There is no need to mix or pre-dissolve, just add it directly to your pool water. This product has also been proven to improve filter efficiency. Start swimming in as little as 15 minutes after application. Keep your pool water sparkling clear and brilliant looking with Smart Shock.

Make sure all pool equipment is working properly, including pump, filter, skimmer and heater. Backwash filter following manufacturers directions. Check alkalinity, pH, and calcium hardness with a test kit. Adjust alkalinity to 125-150 ppm. Adjust pH to 7.4-7.6 by adding a pH decreaser or pH increaser. Adjust calcium hardness to 175-275 ppm. When using other products outlined in directions for this product, always follow directions on those products.

Routine Maintenance:

With pump running, broadcast 1 lb. of BioGuard Smart Shock per 12,000 gallons of pool water, directly into pool around edges.
Brush any undissolved product off pool surfaces.
Wait at least 15 minutes after product application before entering pool.
Operate pump and filter continuously for 48 hours after product addition.
For best results, apply product weekly as part of your maintenance routine.

If Light Algae Present:

Vacuum leaves and any other foreign debris from pool. Brush visible algae thoroughly from pools surface with a surface-compatible brush.
Brush any undissolved product off pool surfaces.
With pump running, broadcast 1 lb. of BioGuard Smart Shock per 12,000 gallons of pool water, directly into heavy algae areas of the pool.
Operate pump and filter continuously for 24 hours after product application.
Afterwards, repeat brushing of pool surfaces.
Do not enter the pool until the free chlorine residual is 1-4 ppm.
If necessary repeat the treatment.

BioGuard Super Soluble is a quick dissolving chlorine concentrate. It is designed to eliminate bacteria without upsetting the balance of the pool water. This product leaves no residue to cloud the water and is safe for use in all types of pools. It has 56% available chlorine and is comprised of 97% active ingredients. The formula of this product has been proven to not lower pH. Super Soluble is an ideal choice for sanitizing small, above-ground pools, and in-ground vinyl-lined pools.

Ensure all pool equipment is working properly. Backwash the filter system following manufacturers directions. Adjust the pH to between 7.2-7.6. Add stabilizer to establish a minimum level of 30-40 ppm to reduce degradative effects of sunlight upon the chlorine residual. Check for metals. Before using this product, add stain and scale inhibitor to prevent staining fo pool surface due to metals. When using other products as outlined in the directions for this product, always follow directions on those products

With pump running, broadcast 4 oz. of this product per 10,000 gallons directly into the water in the deep end of the pool as an initial treatment. Repeat additions until a residual of 1-3 ppm chlorine is established as determined by the way of a test kit. To prevent damage to pool surface, use a pool brush to disperse granules that may have settled to the bottom of the pool. Never allow undissolved product to rest in contact with bleachable pool surfaces. Regular use of a test kit is necessary to determine when it is necessary to add another dose of this product to maintain a residual of 1-3 ppm available chlorine in the pool water. An average daily dose requirement is 2-3 oz. of this product per 10,000 gallons of water. After use of this product it is recommended that a preventative algae treatment be added on a weekly basis.

Super Chlorination:

Broadcast 1 pound of this product per 10,000 gallons directly into the water in the deep end of the pool. To prevent damage to pool surface, us a pool brush to disperse granules that may have settled to the bottom of your pool. Never allow undissolved product to rest in contact with bleachable pool surfaces.

In water temperatures less that 70 degrees or as an alternate application procedure, predissolve this product prior to applying evenly to the deep end of the pool. Dissolve this product outdoors, in a clean plastic bucket stirring with a clean plastic or wooden spoon. Add this product to water, Never add water to product. Never add more than 1 lb of this product to less than 3 gallons of cool water. Do not mix with other products when predissolving.

BioGuard Brominating Tablets are a totally soluble sanitizing alternative to chlorine. They are designed for use in brominators and because bromine typically dissolves slower than chlorine, this mode of sanitation may require less maintenance. Also, because bromine causes fewer odors than chlorine, it is ideal for indoor pools. These bromine tablets are effective in a wide range of pH levels. This product will provide continuous killing of bacteria and is recommended for pools with recurring algae problems.

Ensure all pool equipment is working properly. Backwash the filter system following manufacturers directions.
Adjust pH to between 7.2-7.6. When using other products as outlined in directions for this product, always follow directions on those products.
A bromine or chlorine residual of 1-2 ppm must first be established in the pool. If the residual is establish with this product in a brominator, use the brominator at the highest feed rate following manufacturers recommendations.
When the bromine residual reaches 1-2 ppm, adjust the feeder accordingly. To maintain bromine residual, adjust the brominator feed rate to assure a constant treatment level of 1-3 ppm in residential pools, and 3-5 ppm in commercial pools.

Regular use of a test kit or test strips is necessary to maintain a bromine residual in the pool water.

BioGuard Basic Tabs are just what the name implies, your standard no-frills 3 inch chlorine tablet. The concentrate long lasting tabs are just what the cost saving customer is looking for. You can rest assured knowing your pool will stay clean with the Basic Tabs because they have the BioGuard name on them.

When used in automatic chlorinator and floaters:

This can be used in feeding mechanisms such as automatic chlorinator and floaters as a maintenance treatment. Fill unit with this product and adjust the feeding mechansim to assure a constant treatment level of 1-4 ppm available chlorine in the pool water. Normally 1-2 ounces of this product per 10,000 gallons will be needed on a daily. Use a test kit or test strips to onitor chlorine levels and adjust the chlorine feed mechanism as needed. Check and reill chlorinator as needed. Do not let this product com in direct contact with vinyl liners or other bleachable surfaces as damage may occur.

When used in skimmers:

This product may be used in plastic skimmers only if skimmer and piping between skimmer and pump ar plastic. Do not add other chemicals through the skimmer when using this product in skimmer as an explosion or fire may result. Do not turn pump off for mor than 8 hours in vinyl pools when this product is in skimmer. Initially add one of this product per 10,000 gallons of water. Add additional product as determined by a test kit or test strips to maintain chlorin residual of 1-4 ppm.

BioGuard CLC Classic Granular Chlorine (25 lb) 68% Calcium Hypochlorite Kills Bacteria, Control Algae, Destroys Organic Contaminants Does not lower pH or destroy total alkalinity Can be used with all swimming pool surfaces. For any application method you choose: No one can be in the swimming pool when chemicals are being added directly to the swimming pool. Do not mix this product with other chemicals, including any other pool chemicals of any kind, such as other disinfection or ‘shock’ products. Do not mix this product. For best results, test your swimming pool water prior to addition of this product. CLC Classic can be added by broadcasting the dry granules over the swimming pool water surface at the deepest end of the swimming pool while the pump is running. Should any of the granules settle at the bottom of the swimming pool, use a pool brush to disperse them.

Kills bacteria, controls algae, destroys organic contaminants
Restores sparkle and clarity to your swimming pool
Calcium Hypochlorite

BioGuard Power Chlor is a compound action chlorinating formulation. It sanitizes, shocks, clarifies and kills algae.

Safe For All Pool Surfaces
Contains Sun Shield To Protect From Sunlight
Compatible With Saltwater and Chlorine Pools
Product pH of 3.9

Initial Start-Up:

Use this method if you are opening your pool in the spring, the pool has not been maintained for several weeks, or if the pool is freshly filled. Add 1 lb of this product per 10,000 gallons of pool water. After 2 hours, test the chlorine level (residual). Repeat dosage until you obtain a 1-4 ppm chlorine level.

Routine Chlorination:

Add 2 to 4 oz of this product in dry form per 10,000 gallons of pool water every day, every other day, or as often as needed to maintain a 1-4 ppm chlorine level.

Shock Treatment:

For best results, apply product weekly as part of your maintenance routine, when bather loads are high, water appears dull or hazy, unpleasant odors, eye irritations occur, or after heavy consistent rain. Add 1 lb of this product per 10,000 gallons of pool water.

Algae Treatment:

With pump operating, brush algae from pool surfaces. Add 1 lb of this product per 10,000 gallons of pool water for light algae growth. Add 2 lb of this product per 10,000 gallons of pool water for moderate to heavy algae growth. If necessary, repeat the treatment.

BioGuard SilkGuard Complete Multi-Benefit Chlorinating Sticks are a revolutionary product exclusive to BioGuard. These chlorine sticks differ from traditional chlorine because the SilkGuard Technology actually softens the water by attaching to hard water components and metal surfaces, which protects your pool surface and equipment from scale, corrosion and staining, all while killing bacteria. SunShield Technology offers protection from the sunlight while the SmartGuard Technology helps the tablets last longer than traditional chlorine tablets. Last but not least Algae killing crystals help stop algae before it starts.

Before you begin:

Ensure all pool equipment is working properly. Clean or backwash filter following manufacturer’s directions. Adjust pH to between 7.2-7.6. In chlorinated pools, add stabilizer to establish a minimum stabilizer level of 30-40 ppm to reduce the degradative effect of sunlight upon the chlorine residual. When using other products as outlined in the directions for this product always follow directions on those products.

Do not add other chemicals into the feeder or floater when this product is in use. as a fire or explosion may occur. To avoid damage to pool surface or materials do not allow product to come in direct contact with these materials. Do not throw tablets directly into pool.

Start-Up/Initial Treatment:

If water is cloudy or green, super chlorinate pool with appropriate shock product until pool is clear. Add 16 ounces of this product (approximately 2 sticks) per 10,000 gallons of pool water to feeder or floater. Adjust the feeder or floater following manufacturer’s instructions to establish a fee available chlorine level between 1-4 ppm. Allow water to circulate at least 4 hours and then test for the free available chlorine level. When the free available chlorine level is adjusted to 1-4 ppm, add the preventative algicide appropriate to your needs.

Routine Maintenance:

Add 16 ounces of this product (approximately 2 sticks) per 10,000 gallons of pool water per week, or as often as needed, to the floater or feeder to maintain a constant free available chlorine level of 1-4 ppm. Sunlight, rainfall, temperature, number of swimmers, and frequency of pool use affects the rate of chlorine residual loss so check the floater or feeder often and refill as needed.

Re-entry into treated swimming pools is prohibited when free available chlorine levels are above 4 ppm due to rich of body injury.

BioGuard SilkGuard Complete Multi-Benefit 3 Inch Chlorinating Tablets are a revolutionary product exclusive to BioGuard. These chlorine tablets differ from traditional chlorine because the SilkGuard Technology actually softens the water by attaching to hard water components and metal surfaces, which protects your pool surface and equipment from scale, corrosion and staining, all while killing bacteria. SunShield Technology offers protection from the sunlight while the SmartGuard Technology helps the tablets last longer than traditional chlorine tablets. This tablet can be used in a skimmer, feeder, or floater. Last but not least Algae killing crystals help stop algae before it starts.

Before you begin:

Do not add other chemicals into the skimmer, feeder or floater when this product is in use. as a fire or explosion may occur. To avoid damage to pool surface or materials do not allow product to come in direct contact with these materials. Do not throw tablets directly into pool.

Start-Up/Initial Treatment:

If water is cloudy or green, super chlorinate pool with appropriate shock product until pool is clear. Add 16 ounces of this product (approximately 2 tablets) per 10,000 gallons of pool water to feeder or floater. Adjust the feeder or floater following manufacturer’s instructions to establish a fee available chlorine level between 1-4 ppm. Allow water to circulate at least 4 hours and then test for the free available chlorine level. When the free available chlorine level is adjusted to 1-4 ppm, add the preventative algicide appropriate to your needs.

Routine Maintenance:

Add 16 ounces of this product (approximately 2 tablets) per 10,000 gallons of pool water per week, or as often as needed, to the floater or feeder to maintain a constant free available chlorine level of 1-4 ppm. Sunlight, rainfall, temperature, number of swimmers, and frequency of pool use affects the rate of chlorine residual loss so check the floater or feeder often and refill as needed.

Re-entry into treated swimming pools is prohibited when free available chlorine levels are above 4 ppm due to rich of body injury.

BioGuard SilkGuard Complete Multi-Benefit 1 Inch Chlorinating Tablets are a revolutionary product exclusive to BioGuard. These chlorine tablets differ from traditional chlorine because the SilkGuard Technology actually softens the water by attaching to hard water components and metal surfaces, which protects your pool surface and equipment from scale, corrosion and staining, all while killing bacteria. SunShield Technology offers protection from the sunlight while the SmartGuard Technology helps the tablets last longer than traditional chlorine tablets. This tablet can be used in a skimmer, feeder, or floater. Last but not least Algae killing crystals help stop algae before it starts.

Before you begin:

Start-Up/Initial Treatment:

If water is cloudy or green, super chlorinate pool with appropriate shock product until pool is clear. Add 16 ounces of this product (approximately 27 tablets) per 10,000 gallons of pool water to feeder or floater. Adjust the feeder or floater following manufacturer’s instructions to establish a fee available chlorine level between 1-4 ppm. Allow water to circulate at least 4 hours and then test for the free available chlorine level. When the free available chlorine level is adjusted to 1-4 ppm, add the preventative algicide appropriate to your needs.

Routine Maintenance:

Add 16 ounces of this product (approximately 27 tablets) per 10,000 gallons of pool water per week, or as often as needed, to the floater or feeder to maintain a constant free available chlorine level of 1-4 ppm. Sunlight, rainfall, temperature, number of swimmers, and frequency of pool use affects the rate of chlorine residual loss so check the floater or feeder often and refill as needed.

Re-entry into treated swimming pools is prohibited when free available chlorine levels are above 4 ppm due to rich of body injury.

BioGuard Arctic Blue Winter Kit will help protect your pool water against staining, algae growth, bacteria and all other threats throughout the long winter months, eliminating much of the work from spring openings. Its formula is compatible with most common sanitizing systems and will drastically cut the amount needed to treat your pool next season, saving you money.

Arctic Blue Shock:

Broadcast the entire dosage into the deep end of the pool.
Brush any undissolved product off the surface of the pool with a compatible brush.
Continue to circulate the pool for a minimum of 30 minutes before proceeding to the next step in the winterization process

It is recommended that as part of the closing procedures, a quality winterizing algaecide be applied following the application of this product.

For mesh covered or non-covered pools, a mid-winter treatment may be required using an appropriate BioGuard sanitizer.

Arctic Blue Algae Protector:

Prior to application:

Test your pool water and follow directions to properly balance your water for conditions in your area. If metals testing indicate a need to use a stain and scale inhibitor, apply that product per label directions. Allow the pool to circulate at least 1 hour before adding other products.

Application

Add the appropriate amount of winter shock according to label directions of the product. Allow to circulate 2-4 hours. Then pour Arctic Blue Algae Protector into the pool around the edges with the pool circulation system operation. Circulate pool water for 1 hour. Then, clean filter and pool walls at water line.

In areas with severe freezing, drain pool equipment and plumbing lines or use an antifreeze recommended for swimming pool plumbing and equipment.

BioGuard arctic blue winter kit is a premium off-season kit. each kit contains arctic blue algae protector, arctic blue shock, and winterizing instructions. Arctic blue algae protector prevents the growth of all types of algae and is approved for use with all filter types arctic blue shock will oxidize and clarify through the off-season months and it is ideal for all pool surfaces. using the arctic blue winter kit in the off-season will make opening in the spring much easier.

Broadcast the entire dosage into the deep end of the pool. brush any undissolved product off the surface of the pool with a compatible brush continue to circulate the pool for a minimum of 30 minutes before proceeding to the next step in the winterization process bioguard arctic blue winter algaecide: Add the appropriate amount of winter shock according to label directions of the product allow to circulate 2-4 hours. then pour arctic blue algae protector into the pool around the edges with the pool circulation system operation circulate pool water for 1 hour then, clean filter and pool walls at water line in areas with severe freezing, drain pool equipment and plumbing lines or use an antifreeze recommended for swimming pool plumbing and equipment.

BioGuard Pool Closing Complete provides the final touch for pool closings. A concentrated 3-in-1 formula helps save time and prevent issues at opening as well as protecting pool surfaces and equipment during the cold weather months. This product works perfect with the BioGuard Arctic Blue Winter Kits.

Before Applying BioGuard Pool Closing Complete:

Make sure all pool equipment is working properly, including pump, filter, skimmer and heater. If needed, backwash and/or clean filter according to manufacturer’s directions. Follow manufacturer’s directions for winterizing equipment.

As Part of the Pool Closing Process:

Shake well before using. Apply entire bottle (72 fl oz) for up to 25,000 gallons of pool water. For pools less than 12,000 gallons, apply half the bottle.
Apply slowly and directly into water while walking around deep end of pool.
Allow pump and filter to operate for at least 2 hours after application.

BioGuard Arctic Blue Floater (3.5 lb) is the perfect solution for continuous winter chlorination in white plaster pools. This should not be used in any pool other than white plaster. This floater features SilkGuard technology that coats metal surfaces, protecting them against rust.

Before using this product the pool water should be properly balanced and appropriately treated with winterizing product appropriate for the geographic area. Consult your BioGuard Dealer for proper winterization procedures.

Ager winterization procedures are complete, place this product into the center of the pool in the deep end. If the tables in the floater dissolve completely and the pool water temperature is above 60 degrees for 40 to 45 days, an additional application is recommended. For cover pool, pull the cover back from the deep end of the pool an adequate distance to allow this products to be placed away from the sides of the pool Monitor pool water temperature and reapply every 30 to 45 days when water temperature is above 60 degrees.

Test and balance water before using this product. Adjust pH to 7.4-7.6. Total Alkalinity to 125-150 ppm. and make sure the pool has a chlorine residual between 1-4 ppm.
Adjust the flow control ring to the three-hole setting.
Place floater in the center of the deep end of the pool and hold upright until it fills with water. Then leave to float.
Dispose when the floater has tipped on its side. Replace as previously directed.

BioGuard Winter Arctic Blue Algae Protector prevents the growth of all types of pool algae and aids in maintaining pool water clarity during the winter when the pool is not in use. Arctic Blue Algae Protector is formulated for use in chlorinated or brominated sanitized swimming pools of all surface and filter types.

Prior to application:

Application

In areas with severe freezing, drain pool equipment and plumbing lines or use an antifreeze recommended for swimming pool plumbing and equipment.

BioGuard Arctic Blue Shock is the perfect first step in winterizing your pool, killing off bacteria, algae, and other contaminants that can wreak havoc on your pool during the long winter months. Its powerful granular formula can be quickly broadcast into your pool without needing dilution, saving you from handling messy liquids. When used in conjunction with an effective algaecide, your pool will stay clean and healthy throughout its winter slumber, making spring openings much faster and hassle-free. Best of all, Arctic Blue Shock is made right here in the USA to ensure the highest quality, allowing you to buy with confidence.

Broadcast the entire dosage into the deep end of the pool.
Brush any undissolved product off the surface of the pool with a compatible brush.
Continue to circulate the pool for a minimum of 30 minutes before proceeding to the next step in the winterization process

It is recommended that as part of the closing procedures, a quality winterizing algaecide be applied following the application of this product.

For mesh covered or non-covered pools, a mid-winter treatment may be required using an appropriate BioGuard sanitizer.

BioGuard Mineral Springs Beginnings is the first step in the Bioguard Mineral Springs System. Beginnings creates a total mineral bathing environment and is a natural way to automatically sanitize pool water. The Mineral Springs System utilizes easy-to-apply minerals and a chlorine generator to produce a chlorine sanitizer. It takes only five minutes a week to maintain – in fact, once you’ve begun the system, you only have to add the Renewal product once a week. The Mineral Springs System is ideal for pools of any size or surface, pools equipped with any chlorine generator, frequent travelers or vacation-takers, and those looking for the luxuries of a mineral pool.

*Special Note: This product will not ship to the state of California.

Backwash and clean filter. Balance your pool water and adjust pH between 7.4-7.6. Add 1 bag of this product per 1000 gallons of water. Determine number of bags needed: pool water volume/1000 = number of bags. Apply evenly at deep end of pool with pump operating. Brush any undissolved product from the bottom of the pool. Temporary clouding may occur.

BioGuard Mineral Springs Renewal replenishes lost mineral levels and rejuvenates the Mineral Springs System. It is step 2 in the system. The Mineral Springs System utilizes easy-to-apply minerals and a chlorine generator to produce a chlorine sanitizer. It takes only five minutes a week to maintain – in fact, once you’ve begun the system, you only have to add the Renewal product once a week. The Mineral Springs System is ideal for pools of any size or surface, pools equipped with any chlorine generator, frequent travelers or vacation-takers, and those looking for the luxuries of a mineral pool.

*Special Note: This product will not ship to the state of California.

To maintain soft, gentle, sparkling water, add one pound (approximately 1-1/2 cups) of renewal per 5,000 gallons of water per week.
Broadcast evenly around the edges in the deep end of the pool when the pool is not in use.
Add when pump and filter are running.
Reapply after heavy rain showers (2 inches of rain withing 24 hours).
Have your pool water tested monthly by your BioGurad Mineral Springs Dealer.

BioGuard Mineral Springs Stain and Scale is the second step in the Mineral Springs pool system, and helps rid your chlorine generators, plumbing, and other equipment of nasty scale buildup and stains. To prevent this, simply apply Stain and Scale at the start of your pool season and treat your pool weekly with Mineral Springs Renewal to keep your Mineral Springs-equipped pool running at optimal levels. This product is part of the Mineral Springs System produced by BioGuard, an industry leader in pool and spa supplies for more than 40 years, allowing you to buy with confidence.

With filtration system running, pour proper dosage directly into the deep end of the pool.
Allow pool water to circulate for 24 hours after application.
Follow up application of Mineral Springs Stain and Scale is required once a season at start up.

BioGuard Skim mor uses a mycelx coated material which traps oils, cosmetics, lotions, pollen, and pieces of fine debris your filter may miss. These impurities can dull your pool water, cause a waterline build-up, and even clog your cartridge or DE filter. This product stretches to fit virtually all skimmer baskets. It is proven to extend the life of the filter and to reduce maintenance time. Other skimmer socks are not coated with mycelx, but skim mor is.

Place Skim-Mor inside skimmer baskets and stretch over basket rim. If basket floats, put small weight (stone) into basket. Chlorine tablets and sticks should be placed into skimmer basket beneath the Skim-Mor.

BioGuard Sparkle Up is a cellulose filter aid intended to be used when your filter experiences difficulty in filtering very small particles. This product helps the filter remove tiny particles of dirt, plaster dust, dead algae, pollen, and other small bits of debris. It also helps prevent metals, which prevents staining. Each container contains about 11-12 cups of product. Sparkle Up has been proven to enhance filter performance and it is approved for use in all filter types.

D.E. Filters:

1 part Sparkle Up and 2 parts D.E. to equal normal filter change.

Cartridge Filter:

8 Cups per 100 sq ft of filter area.

Sand Filters:

1 Cup for 12 in Diameter Filters
2 Cups for 18 in Diameter Filters
4 Cups for 24 in Diameter Filters
6 Cups for 30 in Diameter Filters
9 Cups for 36 in Diameter Filters
13 Cups for 42 in Diameter Filters
17 Cups for 48 in Diameter Filters

Before using this product, make sure the filter, hair and lint pot and skimmer baskets are clean. To obtain uniform distribution of this product, mix the required amount in a clean bucket of water and add the slurry slowly through the skimmer with the pump on. Follow specific directions below for your type of filter.

D.E. Filters:

Thoroughly backwash filter. Set filter to normal filter position. Prepare a mixture of 1 part this product and 2 parts D.E. in sufficient quantity to make up the normal filter charge. Mix the D.E. and this product together in water. Coat the filter with this mixture, as you normally would using D.E. alone. Operate as usual until a new charge is required.

Sand Filters:

Backwash filter thoroughly. Set filter to normal filter position. Add this product according to usage directions using amounts specified in chart below. Run filter continuously. Backwash after 24 hours sooner if the pressure guage reaches the maximum recommendations. Repeat if necessary to clear water completely.

Cartridge Filters:

Remove and clean cartridge. Seat cartridges properly in the filter. With pump running, add 8 cups of this product per each 100 square feet of filter area. (Refer to directions for use). Clean cartridges when pool clears. or if filter pressure reaches manufacturers recommended maximum. Repeat treatment if necessary. Use this product once a month to help maintain optimum water clarity.

BioGuard PowerFloc clears excessively cloudy water. This product is ideal for use after a rainstorm or a period of time when your pump wasn’t running (perhaps during a vacation). The greater the amount of debris in the water, the faster it works. PowerFloc is very powerful flocculant. It settles suspended particles to the bottom for removal by vacuum and makes water clear and sparkling.

8 fl oz per 10,000 gallons of water.

Cloudy Water:

Shake well before use.
Check filter and backwash or clean filter if necessary.
Adjust pH to 7.5-8.0 for best results.
Use at a rate of 8 fl. oz. per 10,000 gallons.
Remove skimmer basket and any product in the skimmer. Pour PowerFloc slowly into skimmer with the pump on and filter valve in recirculate or whirlpool position. For filters without recirculate position: backwash, then with filter in filter position, dilute PowerFloc into large plastic pail of water (8 fl. oz. of PowerFloc per 1 gallon of water, always add Powerfloc to water, never water to PowerFloc) and apply evenly over surface of pool. Replace Skimmer basket after applying PowerFloc.
Allow Pump to circulate water for 2 hours to distribute PowerFloc throughout the pool.
Shut off the pump. Let PowerFloc settle debris to bottom whil pool remains undisturbed for 12 to 24 hours ( usually overnight). Note: The greater the debris in the water, the faster PowerFloc works. For extremely cloudy pools (cannot see the drain in the deep part of pool) use double the normal dosage.
Vacuum all settled debris with filter in waste or drain mode. Note: Settling may continue for several days if new debris is introduced by wind or rain. If so, vacuum waste again. Do not vacuum debris through filter.
Backwash and clean filter with BioGuard Kleen-It and resume normal filter cycle.
Check pH and re-adjust if needed to 7.2-7.6

For Water with Algae:

PowereFloc will not kill algae but facilitates the removeal of dead algae after treatment. BioGuard has a number of specific algae treatments. Follow the directions on the product you choose to treat algae.
After the algae treatment is complete per the algae treatments label directions, follow steps 1 through 8 as previously stated for cloudy water.

BioGuard Natural Result helps to control odors and waterline buildup caused by oils, lotions, greases and other organic contaminants as they enter your pool. By using a broad spectrum of natural enzymes designed for use in swimming pools, BioGuard Natural Result can help reduce the maintenance on filters and pool surfaces, saving you time and effort.

This product is specifically formulated to work in conjunction with all of the BioGuard Care Systems, including Mineral Springs and Soft Swim. It is compatible with chlorine, bromine, or biguanide systems.

BioGuard Polysheen Blue is a water clarifier that is used to clear up cloudy water fast. It works on small suspended particles in the water. This product is highly concentrated, so a little goes a long way. It can be used with all pool and filter types and does not affect pH level. This product also assists in the filtration of cloudy water. Restore your pool water to sparkling blue with Polysheen Blue.

1 fl oz per 5,000 gallons of water per week.

Apply Polysheen Blue at a rate of 1 oz. per 5,000 gallons of pool water.
Apply slowly and directly into water while walking around de
Allow pump and filter to operate for at least 8 hours after application.
If after 36 hours the water is still cloudy reapply at a rate of 1 oz. per 5,000 gallons of pool water.

BioGuard Natural Clarifier uses a natural ingredient, Chitosan, to help keep your pool water sparkling and your filter working at peak efficiency. BioGuard Natural Clarifier should be part of your weekly pool maintenance program, it may also be used to cure cloudy water

Keeps your water sparkling and your filter working at peak efficiency
Biodegradable and contains no dye or fragrance
Works with natural ingredient, Chitosan (made from crustacean exoskeletons), to capture sediment particles
Suitable for all pool surface types and all treatment types

Apply Natural Clarifier at a rate of 1 fl oz per 5,000 gallons of pool water.
Apply slowly and directly into the water while walking around the deep end of the pool.
Allow pump and filter to operate for at least 12 hours after application.
For very cloudy water, double or triple the dose

BioGuard Pool Tonic is formulated to remove phosphate and contaminants too small to be caught by the filter. Every day the environment, swimmers and even pets introduce to your pool unwanted contaminants like phosphate, skin oils, dirt, dust, pollen, etc. These contaminants can cause your pool water to look cloudy, hazy and dull. The dual-action formula binds to these impurities and makes them large enough to be filtered out.

Used as part of an algae treatment for deal algae removal.
One bottle removes 1000ppb of phosphate per 80,000 liters of pool water

Always read the label prior to application
Backwash and rinse your sand filter, or rinse your cartridge filter.
Shake well before using.
Pour along the edges of the pool.
Run pump continuously for 24-48 hours.
Keep an eye on your filter’s pressure. Backwash as needed.

BioGuard Smart Shield is the ultimate in pool water conservation. This product reduces water evaporation, helping to conserve water and preserve heat. A single application last up to 30 days.

8 oz per 15,000 gallons of water every month.

Shake bottle before using. With the pump running, add 8 fl oz per 15,000 gallons of water. For best dispersion, add Smart Shield in front of pool return lines. Run the pump daily for proper circulation. For larger pools, add 16 fl oz per 1,000 sq. ft of surface area or 30,000 gallons of pool water oncer per month.

BioGuard Pool Complete creates a swimming pool that looks amazing. This unique 3-in-1 high intensity formula delivers results that have to be seen to believe. This product clarifies the water, prevents waterline build-up and removes phosphates.

Apply this product at a rate of 4 fl oz per 10,000 gallons of pool water.

Before Applying: Make sure that all pool equipment is working properly, including pump, filter, skimmer, and heater. If needed, backwash and/or clean filter according to the manufacturers directions.

Shake well before using. This product is not intended for oral consumption.

To keep your water sparkling clear, apply this product weekly at a rate of 4 fl oz per 10,000 gallons of pool water.
Apply slowly and directly into water while walking around deep end of the pool.
Allow pump and filter to operate for at least 12 hours after application.

BioGuard Pool Opening Complete is the perfect product for correcting dirty water from pool openings. The powerful 3-in-1 concentrated formula will aid in quickly cleaning the water of any winter filth and will start to turn the water amazingly clear. Cut down the time spent on cleaning during a pool opening and start swimming faster with just one bottle of Pool Opening Complete.

Shake Pool Opening Complete well before using
Add 125mL of Pool Opening Complete for every 10,000L of pool water
Apply Pool Opening Complete directly to deep end of the pool
Pump should run continuously for a day after application

DO NOT USE POOL OPENING COMPLETE WHILE SWIMMERS ARE IN THE POOL
Wait 15 minutes after using Pool Opening Complete to go swimming

SaltScapes Scale Defender is an anti-scaling product specifically formulated for saltwater pools. SaltScapes Scale Defender is designed to bind that calcium preventing it from sticking to the cell ensuring that the chlorine generation of the salt cell is unhindered.

Salt Pool Truth 3: Chalky-white calcium scale deposits will form on your salt cell’s walls due to the environment in the cell.

Add 1 bottle for every 40,000L of pool water
Backwash or clean filter
Add directly to the pool with the pump running

DO NOT USE SCALE DEFENDER WHILE SWIMMERS ARE IN THE POOL
Wait 15 minutes after applying Scale Defender to go swimming

BioGuard SaltScapes Test Strip Pack provides you with the tools to test all the required levels in your salt water pool. This pack contains 10 strips to test your salt level and 25 strips to test ph, alkalinity, calcium hardness, stabilizer, and chlorine. Simply dip the test strip in the water and match to the chart on the bottle.

Balance Test Strips (Test Weekly)

Obtain an 8 oz pool water sample (from elbow-deep in the pool). Dip entire strip into water and remove immediately.
Hold test strip level for 15 seconds. Do not shake excess water from strip.
Compare total hardness, total chlorine, free available chlorine, pH, total alkalinity and stabilizer pads to color chart on bottle

Salt Level Test Strips (Test Monthly)

Collect a sample of water in a clean small cup. Only about an inch of water is necessary.
Place the test strip into the sample and allow to soak until the yellow band at the top of the strip turns dark.
Remove strip and determine where the top of the light color peak stops. Use the value to compare to the table on the bottle to find the salt level.

Your salt cell generates unstabilized chlorine, which means it diminishes rapidly when exposed to the sun’s UV rays. SaltScapes^® SunShield^® Stabilizer protects generated chlorine from sunlight, allowing it to last longer and be less demanding on your cell system.

Protects against sunlight to extend life of generated chlorine and minimize cell run time
Reduces chlorine consumption and maintenance costs
Improves efficiency of chlorine generator

The process a cell uses to convert saltwater into chlorine contributes to higher water pH every time a cell runs. SaltScapes pH Reducer protects your pool surfaces and equipment by lowering pH to the ideal range. It is also a safer option to store and handle than liquid muriatic acid.

Broadcast into deep end of pool while not in use and your pump is running. All water to circulate for at least two hours then test for ideal pH of 7.2-7.6.

BioGuard SaltScapes Cell Cleaner is just what you need to keep your chlorine generator running at peak performance. This Cell Cleaner aids in removing built-up scale from your cell to restore it to peak performance. With this simple to use product you can clean your cell in as little as 15-30 minutes.

BioGuard Salt Scapes Algae Remover is a highly effective, non-staining algaecide that kills algae in swimming pools. Salt Scapes Algae Remover is effective at killing green, blue-green, black and mustard algae. This product is compatible with all pool surfaces and filter types.

Salt Scapes Saltwater Pool Care System was designed specifically for saltwater pools and provides everything you will need to keep your saltwater sparkling and protect your equipment and pool surfaces. Saltwater pools are favored for their simpler and gentler approach to pool care, but they do have some unique needs when compared to traditional chlorine pools.

Use as weekly preventative
For visible algae, add 1 lb. of BioGuard BurnOut 3 per 10,000 gallons of pool water OR 1 lbs. of BioGuard BurnOut 35 per 6,000 gallons of pool water OR 1 lb. of BioGuard Smart Shock per 12,000 gallons of pool water.
Add 16 ounces per 10,000 gallons

BioGuard’s SaltScapes Shock Oxidizer is a chlorine free oxidizer allowing it to eliminate contaminants without creating unwanted effects unlike most oxidizers which leave an odor due to chlorine contents.

Eliminates contaminants for cleaner, fresher water
Designed for salt water pools

Broadcast product into deep end of pool with pump running
Use after or before heavy pool use
Swimming may resume 15 minutes after application

*Always review directions on chemical bottles before application

BioGuard Soft Swim Filter Aid is a powerful flocculant clarifier that is designed to work specifically with any Soft Swim-equipped pools, rapidly eliminating cloudy or hazy water to restore it to its former brilliance. Its granular formula attracts together any microscopic particles in the water, making them heavy enough to settle on the pool bottom for quick vacuum removal. It can also be used to improve filter efficiency, restoring water to the jewel-like clarity you remember. Best of all, Soft Swim Filter Aid is made right here in the USA to ensure quality, allowing you to buy with confidence.

Cartridge & Sand Filters:

1/2 to 1 lb per 10,000 to 35,000 gallons of water.

D.E. Filters:

1 to 2 oz per 10,000 to 35,000 gallons of water.

Flocculant Dose:

1 lb per 6,500 gallons of water.

Cartridge and Sand Filters:

Predissolve outdoors in a clean plastic bucket 1/2 to 1 pound of this product in 1 gallon of water for pools ranging from 10,000 to 35,000 gallons. Stir with a clean plastic or wooden spoon. Pour predissolved solution slowly into the skimmer with the pump running. Filter continuously for 24 to 48 hour or until the pool clears. If the pool does not clear, backwash the filter and repeat as necessary. If the pressure gauge increases 8 to 10 psi above the original pressure, backwash and rinse filter appropriately. Resume routine maintenance schedule.

D.E. Filters:

Backwash and clean filter according to the manufacturers instructions and return filter to normal cycle. For pools ranging from 10,000 to 35,000 gallons, predissolve 1 to 2 ounces of this product outdoors in a clean plastic bucket using 1 gallon of water. The slurry can be stirred with a plastic or wooden spoon. Slowly add the slurry into the skimmer with the pump running. Filter continously for 24 to 48 hours or until the pool clears. If the filter pressure increases 8 to 10 psi above normal pressure, backwash and clean filter as necessary.

Flocculant:

Backwash and rinse filter according to manufacturers instructions. Test pH and adjust to 7.6 to 7.8. Allow pool to circulate for 2 hours before proceeding to the next step if pH adjustment was necessary. Raise the water level in the pool to the top of the skimmer box and turn pump off. Usde this product at a rate of 1 pound per 6500 gallons of pool water. Predissolve outdoors in an empty plastic bucket 1 pound of this product with 1 gallon of water. Stir with a plastic or wooden spoon. Pour the solution along the edges of your pool. Allow 24 to 48 hours for the flocculant to settle on the bottom and slowly vacuum out. If some of the floc becomes suspended, allow an additional 24 hours for it to settle and then slowly vacuum out. Check and adjust pH and total alkalinity as necessary and resume normal maintenance.

BioGuard SoftSwim C is a powerful clarifier and oxidizer that helps keep the sparkle in your water longer by removing contaminants that can cause cloudiness. It is step 3 of the SoftSwim program. This product is formulated to last 30% longer in the water – a real money saver. It clears pool water by eliminating body oils, perspiration, and other undesirable contaminants that can affect clarity and sparkle. SoftSwim C has a built-in stabilizer to ensure that the dual action chemicals won’t burn off easily in hot weather.

Initial Start Up:

1 gallon per 10,000 gallons of water.

Routine Maintenance:

1 gallon per 10,000 gallons of water per month.

Cloudy Water Treatment:

2 gallons per 10,000 gallons of water.

Winterizing:

1 gallon per 10,000 gallons of water.

Start Up:

Before opening your pool for the season, take a sample of your pool water to your BioGuard Authorized Dealer for a complete water analysis. Once your pool water has been properly balanced, add SoftSwim A according to label directions. Add one gallon of SoftSwim C per 10,000 gallons of pool water. Allow the water to circulate for 24 hours. Then adjust the SoftSwim B to 50 ppm. Resume routine maintenance as instructed by the SoftSwim Pool Care Guide.

Routine Maintenance:

Once each month, add SoftSwim C at a rate of 1 gallon per 10,000 gallons of pool water to maintain sparkling clear water. With the filter operating, pour SoftSwim C directly into the water in several areas of the pool. Allow treatment to circulate throughout the pool for at least 30 minutes before swimming. (Note: Excessive rain, high temperatures or heavy bather loads may require more frequent additions of SoftSwim C (consult your SoftSwim Dealer for additional details.)

Clearing Cloudy Water:

Improperly cleaned filters are the primary cause of cloudy water in SoftSwim pools. Clean filter with SoftSwim Filter Cleaner following label directions. (Note: For best results, filters should be cleaned every 6 weeks) Add SoftSwim C at a rate of two gallons per 10,000 gallons of pool water. Use BioGuard SoftSwim Filter Aid to enhance clearing of cloudy water. If the condition persists, take a sample of your pool water to you BioGuard Authorized Dealer for further recommendations.

Winterizing:

To winterize your pool, simply add SoftSwim A and SoftSwim B according to label directions and add 1 gallon of SoftSwim C per 10,000 gallons.

BioGuard SoftSwim B is the sanitizer that contains biguanide and is step 2 in the Soft Swim program. This step kills and controls harmful bacteria and is gentle on eyes, hair, and skin. SoftSwim B is UV-shielded and is resistant to evaporating in the sun. The SoftSwim program is ideal for in-ground or above-ground pools containing less than 25,000 gallons of water, pools that have bottom drains, and pools that have excellent circulation with the pump operating at least 12 hours per day. SoftSwim sanitizes with biguanide.

Start Up:

1/2 gallon per 10,000 gallons of water to get a content of 50 ppm.

Routine Maintenance:

1 pt per 10,000 gallons of water to raise level by 10 ppm.

Freshly Filled and Dechlorinated Pools – Start-Up With Softswim B:

If the pool water contains algae or is hazy, consult the “The Pool Care Guide for SoftSwim.” available at your BioGuard Authorized Dealer.
Backwash or clean pool filter. Check pool pH.; adjust to 7.2-7.8 if necessary.
Add SoftSwim B to give a content of 50 ppm (1/2 gallon product/10,000 gallons of pool water).
After 24 hours, check pH and SoftSwim B concentration with a test kit and adjust if necessary.

Routine Maintenance:

Every week, check SoftSwim B concentrated and pH.
Maintain SoftSwim B concentrated at about 50 ppm. If concentration falls 10 ppm or more, add a top-up dose.

BioGuard SoftSwim A is an algaecide. Using an effective algaecide is an important first step in the SoftSwim program. This product protects against a broad spectrum of algae. It is formulated to remain stable against the UV rays of the sun and against high temperatures.The SoftSwim program is ideal for in-ground or above-ground pools containing less than 25,000 gallons of water, pools that have bottom drains, and pools that have excellent circulation with the pump operating at least 12 hours per day. SoftSwim A sanitizes with biguanide.

Initial Application:

32 fl oz per 25,000 gallons of water.

Routine Maintenance:

1 fl oz per 5,000 gallons of water per week, or 2 fl oz per 5,000 gallons of water every 2 weeks.

Ensure all pool equipment is working properly. Backwash the filter system following manufacturers directions.
Adjust pH to between 7.2.-7.6.
Check for metals and if present add a stain and scale inhibitor to prevent staining of pool surface due to metals.
Wait at least 15 minutes after application before entering pool.
For Initial Application or When Pool Water is Changed: pour 32 oz. directly into pool per 25,000 gallons of water.
For Routine Maintenance Dose: For weekly application intervals, use 1 oz. per 5,000 gallons of water. For 2 week application intervals, use 2 oz. per 5,000 gallons of water every other week. Following heavy rain showers, add an additional 1 oz per 5,000 gallons.

BioGuard SoftSwim Stain Control helps prevent metals from settling in the water and staining pool surfaces. This product is intended for use in pools with plaster surfaces, or on any surface where dissolved metals such as iron, copper and manganese are present. Stain Control also helps maintain the presence of SoftSwim B and C. Each SoftSwim product is formulated to work specifically with the biguanide chemistry of the SoftSwim program.

Routine Maintenance:

16 fl oz per 10,000 gallons during start up or if significant make-up water added.

Metal Treatment:

32 fl oz per 10,000 gallons of water for every 2ppm of metals.

Fresh Stain Removal:

32 fl oz per 10,000 gallons of water.

Treatment of Metals in Pool Water:

Backwash filter, then allow pump to run continuously. If the total amount of metals present in pool water exceeds 2 ppm, also use BioGuard Sparkle Up Filter Aid to help remove metals.

Use 1 quart of BioGuard SoftSwim Stain Control per 10,000 gallons of water per 2 ppm of metals. Add directly to the pool in the area of any localized metal stain. Backwash the filter as need is indicated. Never allow filter pressure to exceed the limit established by the manufacturer.

Removal of Fresh Stains:

Many fresh metallic stains can be removed by the addition of BioGuard SoftSwim Stain Control. Using a treatment of 1 quart per 10,000 gallons fo water, add BioGuard SoftSwim Stain Control directly to the pool in the area of the stain. Brush the stain area daily for 5 to 7 days. Repeat for large heavy metal stains. Consult your authorized dealer regarding aged stains.

For pools treated with BioGuard Softswim B:

Must be used when starting a white plaster pool on BioGuard SoftSwim B wheather metals are present or not.
When Metals are present in any pool type or make-up water.
Spring start-up and make-up water refills. Have water analyzed by BioGuard Authorized Dealer for metals. Add 1 quart of SoftSwim Stain Control per 10,000 gallons to control up to 2 ppm metals and follow directions above

BioGuard Soft Swim Test Strips are designed to test pool water for the chemicals used in the Soft Swim program. These strips are easy to use and reveal results quickly and accurately. Pool experts recommend that Soft Swim Test Strips should be used weekly to ensure properly balanced water. This product works only with pools on the Soft Swim program. Each Soft Swim product is formulated to work specifically with the biguanide chemistry of the Soft Swim program.

Dip Strip into water for 1 second, remove.
Hold strip level for 30 seconds.
Compare total alkalinity, pH, and SoftSwim C (in that order) to the color chart.
Re-Dip the strip and rapidly move strip back and forth underwater for 30 seconds.
Compare bioguanide part to color chart.

Soft Swim B:

The SoftSwim B levels should register between 30- 50 ppm. If below add more SoftSwim B. Read SoftSwim B directions for proper dosing.

Total Alkalinity:

The Total Alkalinity level should register between 125 and 150 ppm. If Total Alkalinity is high add BioGuard Lo N Slo. If total alkalinity is low add BioGuard Balance Pak 100.

pH:

The pH levels should register between 7.2-7.8. If pH is high ad BioGuard Lo N Slo. If pH is low add BioGuard Balance Pak 200 according to label directions.

SoftSwim C:

SoftSwim C should register between 40-60 ppm. If below 40 ppm, add more SoftSwim C per label directions. If over 60 ppm, contact your BioGuard Dealer for guidance.

BioGuard SoftSwim Filter Cleaner is the most effective product available to prevent cloudy water and allow filters to operate at peak performance. It is uniquely formulated to work with any filter type and helps to remove particles specific to the SoftSwim program. This product will improve pool circulation and water clarity by removing dirt, oils, and deposits that can clog filters. Each Soft Swim product is formulated to work specifically with the biguanide chemistry of the SoftSwim program.

Sand and most D.E. Filters:

1 qt per cleaning

Non-Backwashable D.E. and Cartridge Filters:

1 qt for small filter and 2 qt for large filters per cleaning.

Sand and Most D.E. Filters:

Backwash thoroughly. Turn pump off. For most effective results, remove lid from lint pot and pour 1 quart of this product into the pot (If this is not possible, pour the product into the skimmer closest to the filter). With the filter in backwash position, turn pump on for 5-10 seconds or until a slight pink color is seen in site glass or filter discharge. Turn pump off and turn valve to closed position, if available. Let filter cleaner soak for 12-24 hours before backwashing. Backwash filter for at least 2 minutes or until site glass or filter discharge water is clear of color, dirt, and debris. Rinse and return to normal operation.

Non-Backwashable D.E. and Cartridge Filters:

Turn pump off. Remove elements from filter and rinse off debris with a high pressure hose. Immerse completely and soak 12-24 hours in a clean plastic bucket containing 1 quart of this product in 5 gallons of water for small filter elements or 2 quarts of this product in 10 gallons of water for large filter elements. Clean and rinse thoroughly with water using a high pressure hose. Replace elements and resume normal operation. For best performance, allow D.E. filter septum or cartridge element to completely dry before operation.